<![CDATA[Automotive Forum - <font size="4"><span style="color: #3766b1;">General Automotive Help Discussions</font>]]> https://automotiveforum.net/ Mon, 28 Sep 2026 14:32:34 +0000 MyBB <![CDATA[Error p0012 on Peugeot 206 1.4 16v (kfu)]]> https://automotiveforum.net/showthread.php?tid=20834 Tue, 15 Sep 2026 17:32:22 +0000 Doc90]]> https://automotiveforum.net/showthread.php?tid=20834 I would like to share a problem that has been troubling me for several days now, and I would be grateful for any advice from those of you who might have encountered this issue.
Basically, after I replaced the cylinder head gasket, I get the P0012 error in diagnostics. This error refers to a delay in the opening of the intake valves. It is related to the variable valve timing (VVT) on the intake camshaft.
I should note that I have tried various steps: I replaced the solenoid and manually tested its operation; I replaced the camshaft position sensor and the crankshaft position sensor; I also replaced the variable valve timing actuator. I have checked multiple times, and the timing is correct. The variable valve timing actuator is correctly positioned on the camshaft, thanks to the alignment pin, so I would also exclude any incorrect assembly.
I also changed the oil and the filter.
The car starts immediately, but it struggles to move from a standstill; I have to keep the RPMs up, otherwise it stalls. During driving, it jerks and hesitates. The engine warning light doesn’t come on the dashboard, but the error P0012 appears during diagnostics.
I haven’t yet checked the oil pump pressure, even though I don’t think the problem is the pump, since the issue appeared after the head work.
Could it be a faulty reading? Perhaps a loose contact on the wiring to the camshaft sensor? I should verify continuity from the ECU to the sensor connector. I’m not sure.
In sharing this rather strange case with you all, I hope that someone has encountered this problem before, and I thank anyone who can offer advice on this matter.]]> I would like to share a problem that has been troubling me for several days now, and I would be grateful for any advice from those of you who might have encountered this issue.
Basically, after I replaced the cylinder head gasket, I get the P0012 error in diagnostics. This error refers to a delay in the opening of the intake valves. It is related to the variable valve timing (VVT) on the intake camshaft.
I should note that I have tried various steps: I replaced the solenoid and manually tested its operation; I replaced the camshaft position sensor and the crankshaft position sensor; I also replaced the variable valve timing actuator. I have checked multiple times, and the timing is correct. The variable valve timing actuator is correctly positioned on the camshaft, thanks to the alignment pin, so I would also exclude any incorrect assembly.
I also changed the oil and the filter.
The car starts immediately, but it struggles to move from a standstill; I have to keep the RPMs up, otherwise it stalls. During driving, it jerks and hesitates. The engine warning light doesn’t come on the dashboard, but the error P0012 appears during diagnostics.
I haven’t yet checked the oil pump pressure, even though I don’t think the problem is the pump, since the issue appeared after the head work.
Could it be a faulty reading? Perhaps a loose contact on the wiring to the camshaft sensor? I should verify continuity from the ECU to the sensor connector. I’m not sure.
In sharing this rather strange case with you all, I hope that someone has encountered this problem before, and I thank anyone who can offer advice on this matter.]]> <![CDATA[ebs 3 wabco checksum correction]]> https://automotiveforum.net/showthread.php?tid=20833 Tue, 15 Sep 2026 13:46:07 +0000 lander]]> https://automotiveforum.net/showthread.php?tid=20833
https://mega.nz/file/cb5CSQKB#Kon63Y41YM...Eq0lDGOwos

Regards, Lander]]>
https://mega.nz/file/cb5CSQKB#Kon63Y41YM...Eq0lDGOwos

Regards, Lander]]> <![CDATA[Maxus 2024 SRS/Airbag]]> https://automotiveforum.net/showthread.php?tid=20799 Mon, 07 Sep 2026 08:58:54 +0000 lipon]]> https://automotiveforum.net/showthread.php?tid=20799
I have several 2024 Maxus veicles that need SRS/airbag repair.In some cases the airbag system is repaired and the SRS control modulehas been replaced with new one,but I still need to program/code the new module to veicle.

What is the correct procedure or diagnostic software for programming a new SRS module on2024 MAXUS veicles?Is dealer online access required,or is there another solution for independent workshops?

Any help wold be appreciated.

Thanks.]]>
I have several 2024 Maxus veicles that need SRS/airbag repair.In some cases the airbag system is repaired and the SRS control modulehas been replaced with new one,but I still need to program/code the new module to veicle.

What is the correct procedure or diagnostic software for programming a new SRS module on2024 MAXUS veicles?Is dealer online access required,or is there another solution for independent workshops?

Any help wold be appreciated.

Thanks.]]> <![CDATA[Diagbox 7.38 full + instalação]]> https://automotiveforum.net/showthread.php?tid=20668 Sun, 16 Aug 2026 15:16:44 +0000 NILO MENDES]]> https://automotiveforum.net/showthread.php?tid=20668 <![CDATA[CHANGE HOUR USE IN CATERPILLAR?]]> https://automotiveforum.net/showthread.php?tid=20531 Sat, 25 Jul 2026 20:52:32 +0000 Cloudnet507]]> https://automotiveforum.net/showthread.php?tid=20531 <![CDATA[Renault Clio III 2007 SID304 Virgin]]> https://automotiveforum.net/showthread.php?tid=20399 Mon, 06 Jul 2026 22:21:30 +0000 sinan1994]]> https://automotiveforum.net/showthread.php?tid=20399 I have Clio 3 from 2007 with 1.5 dci diesel engine. car was running we change the ups in the front. car was not running after replace the ups modul.
after i try to fix it with renolink. in this moment i confuse it with uch and renewe it. (big shit). so i lost isk code but pin read it with autel. so i try write a dump from internet on uch and try to sync it with ecu but no result. i try to virgin the ecu with obdstar but no sucsess to learn it with autel im608. autel sad ecu is not blank. who can help me ? or give me a tip for a solution?

maybe somone can fix the uch eeprom 
i send uch eeprom and flash from ecu sid304
fin: VF1BR2C0638434070
Pin Code is :A219B915AA6C
ISK : ?????

]]> I have Clio 3 from 2007 with 1.5 dci diesel engine. car was running we change the ups in the front. car was not running after replace the ups modul.
after i try to fix it with renolink. in this moment i confuse it with uch and renewe it. (big shit). so i lost isk code but pin read it with autel. so i try write a dump from internet on uch and try to sync it with ecu but no result. i try to virgin the ecu with obdstar but no sucsess to learn it with autel im608. autel sad ecu is not blank. who can help me ? or give me a tip for a solution?

maybe somone can fix the uch eeprom 
i send uch eeprom and flash from ecu sid304
fin: VF1BR2C0638434070
Pin Code is :A219B915AA6C
ISK : ?????

]]> <![CDATA[Help needed with Truck Xentry intall]]> https://automotiveforum.net/showthread.php?tid=20191 Sat, 06 Jun 2026 05:28:16 +0000 scaNZed]]> https://automotiveforum.net/showthread.php?tid=20191 One for myself and one for my mate.
Can someone please help me, I don't mind paying for your service.
Thanks
I ordered and paid for Truck Xentry on both tablets and only received tablets with Windows 10 PRO
HD is 480GB]]> One for myself and one for my mate.
Can someone please help me, I don't mind paying for your service.
Thanks
I ordered and paid for Truck Xentry on both tablets and only received tablets with Windows 10 PRO
HD is 480GB]]> <![CDATA[VAG Odis Licenses EU]]> https://automotiveforum.net/showthread.php?tid=20154 Sat, 30 May 2026 17:21:32 +0000 Prodrive]]> https://automotiveforum.net/showthread.php?tid=20154 VAG Odis Licenses EU
]]> VAG Odis Licenses EU
]]> <![CDATA[CAN CLIP DLL FILES]]> https://automotiveforum.net/showthread.php?tid=20153 Sat, 30 May 2026 16:58:34 +0000 Prodrive]]> https://automotiveforum.net/showthread.php?tid=20153 CAN CLIP DLL FILES
]]> CAN CLIP DLL FILES
]]> <![CDATA[2016 Acura ILX 2.4L Base Bench Pinout]]> https://automotiveforum.net/showthread.php?tid=18949 Fri, 26 Dec 2025 07:33:00 +0000 Jem@prog]]> https://automotiveforum.net/showthread.php?tid=18949 ]]> ]]> <![CDATA[Ista 4.55.30 problems with patcher]]> https://automotiveforum.net/showthread.php?tid=18316 Sat, 20 Sep 2025 20:16:33 +0000 Beameup11]]> https://automotiveforum.net/showthread.php?tid=18316
i don´t know, whether someone can give me an advice, which commandos ista-patcher needs to start a clean Ilean install of 4.55.30 offline and search vin without user authentification (per pin).

Maybe there is actual no way to do this with ista-patcher? I tested several options, with alway the same result of getting error messages.

I only for private purposes want to  use a clean install without any backdoor software like in every standalone version. So i hope, you could give me the information, which is needed to solve my issue, please.

Best regards,
Beameup11]]>
i don´t know, whether someone can give me an advice, which commandos ista-patcher needs to start a clean Ilean install of 4.55.30 offline and search vin without user authentification (per pin).

Maybe there is actual no way to do this with ista-patcher? I tested several options, with alway the same result of getting error messages.

I only for private purposes want to  use a clean install without any backdoor software like in every standalone version. So i hope, you could give me the information, which is needed to solve my issue, please.

Best regards,
Beameup11]]> <![CDATA[VCDS Issues]]> https://automotiveforum.net/showthread.php?tid=17949 Sun, 06 Jul 2025 11:25:37 +0000 bksdesign]]> https://automotiveforum.net/showthread.php?tid=17949 Also looking for advice on enabling on/start authorization on my 09 Audi, will VCDS do that for me?  I'm having a problem accessing any control module with my VCDS Lite software, the vehicle wont communicate with the program, it used to, but not anymore  any help or advice would be greatly appreciated.
                                                               Thank you in advance!]]> Also looking for advice on enabling on/start authorization on my 09 Audi, will VCDS do that for me?  I'm having a problem accessing any control module with my VCDS Lite software, the vehicle wont communicate with the program, it used to, but not anymore  any help or advice would be greatly appreciated.
                                                               Thank you in advance!]]> <![CDATA[BMW E70-e71 8HP EGS Reset File]]> https://automotiveforum.net/showthread.php?tid=17279 Fri, 04 Apr 2025 16:55:45 +0000 Prodrive]]> https://automotiveforum.net/showthread.php?tid=17279 BMW E70-e71 8HP EGS Reset File

]]> BMW E70-e71 8HP EGS Reset File

]]> <![CDATA[Insignia transmission control module]]> https://automotiveforum.net/showthread.php?tid=17227 Sat, 29 Mar 2025 16:58:17 +0000 bgp1]]> https://automotiveforum.net/showthread.php?tid=17227 I have an insignia from 2009 2.0 CDTI A20DTH.
I had some problems with it (soft close for tailgate, high beam), when i found out it was an automatic, and somewhere was converted to manual, without programing.
My question is, what can i do with this car?

Can I do something with OP-COM or GDS2?
Thanks!]]> I have an insignia from 2009 2.0 CDTI A20DTH.
I had some problems with it (soft close for tailgate, high beam), when i found out it was an automatic, and somewhere was converted to manual, without programing.
My question is, what can i do with this car?

Can I do something with OP-COM or GDS2?
Thanks!]]> <![CDATA[Xentry Keygen Patch Activator Package Collection]]> https://automotiveforum.net/showthread.php?tid=17220 Sat, 29 Mar 2025 07:31:23 +0000 Prodrive]]> https://automotiveforum.net/showthread.php?tid=17220 Xentry Keygen Patch Activator Package Collection

]]> Xentry Keygen Patch Activator Package Collection

]]>